2024 DATES ARE SET AUGUST 2-4 2024
Event Rules:
CLASSES: Street Outlaw, Street Outlaw Dry Tire,
PRIZE POOL BUY IN AND PAYOUT SCHEDULE:
OUTLAW - BUY IN IS $100 Per Bracket, PAYOUT IS TOP 16
Dry Tire Outlaw - BUY IN IS $50 Per Bracket,PAYOUT IS TOP 8
STREET OUTLAW:
Street Outlaw 2023
1. Chassis:
2wd 12-13.5” wheelbase.
Rear Motor and Mid Motor Allowed
No 4wd or 4wd to 2wd conversions.
2. Motor / Speed Control:
Any commonly over the counter 1/10 RC car motor.
Maximum Allowed can size is 550.
** Full Speed Control Timing and Tuning Allowed.
** No "Assist" receivers or gyros, or any driving assist items allowed. No AVC Receivers. No TSM receivers.
3. Battery:
Any commercially available 2s (in store or online) Lithium-Ion Polymer (LiPo), Graphene, or LiPo HV Battery.
Must have a plug or bullet connectors (no hard wiring)
Single battery pack Only! No multi packs plugged in parallel.
A hard case is not required.
A 3D printed case for your pack is encouraged.
3.1 Voltage:
A Maximum of 8.44 Volts will be allowed.
4. Tires:
Front: Any commercially available (in store or online) rubber with foam insert type.
No O-Ring type. Min size 68mm or 2.68 inches
Rear: Any commercially available (in store or online) rubber with foam insert type.
Treaded and slicks acceptable.
4.1 Foam Insert
Foam insert is not required in front or rear tires but maybe ran.
4.2 Prep:
Tire prep is allowed, heating of the tires is allowed post tech. We will have a tape area as well as a area with no tape at the start line. You have the choice of what area you would like to use.
4.3 Burn Out:
A burn out is not required. But we highly encourage it!
5. Shocks:
Must have four shocks each controlling a wheel as intended by typical manufacturers. (Connected and operating hinge pin arms at all four corners of the car.)
Shocks must have movement visible and acceptable by the race director.
6. Transmission:
Car must use a 3-5 gear transmission (gear box)
Belts or link conversions not allowed.
7. Weight:
Cars ready to run must meet a minimum weight of 4.54lbs, 72.6oz, or 2060 grams
8. Wheelie bar:
No item may extend more than 14” from the rear dogbone including any wheelie bar parts or wheels.
8.1 Wheelie Bar Wheels:
Maximum of 1.5” tall wheels.
9. Body:
Must be a realistic looking drag car style body.
Pro Mods Allowed.
Body must cover wheels (i.e. no buggies)
Wheel well must be cut exposing a minimum of 1/2 the wheel.
9.1 Rear Body Cutouts:
The rear section of the body (valance/bumper panel) may be removed to mount a spoiler.
**Must retain the Original rear side quarter fenders, trunk lid and/or pickup bed.**
9.2 Body Holes:
Up to four (4) holes for mounting, no larger than ½” at any location on the body are allowed. Window cut outs Not allowed.
Extra holes will need to be covered in tape or stickers of body has been remounted.
9.3 Spoilers and Splitters:
Rear wings, spoilers, and side dams may extend off the body’s rear deck a max of 3 inches and cannot extend taller than parallel to the roofline.
Rear spoilers supplied with a body are considered legal for that body in their intended design.
Nose splitters may extend a max of 1/2” from the edge of the body.
DRY TIRE STREET OUTLAW
Rules for Dry Tire will follow the same rules as Street Outlaw with the exceptioin of tire rules.
Dry Tire rules:
Tires must be dry when brought to tech inspection.
No Glossy or Shinny tires
Can't leave any sticky residue on tech inspectors fingers.
Cannot pull over 130z on the inspection meter. This is the meter we will use in technical inspection. https://a.co/d/15xX8H8